honeywell_1400g
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revision | Next revisionBoth sides next revision | ||
| honeywell_1400g [2019/04/30 14:41 (5 years ago)] – swind | honeywell_1400g [2019/04/30 14:43 (5 years ago)] – swind | ||
|---|---|---|---|
| Line 25: | Line 25: | ||
| - | The Default settings for the Honeywell 1400G Serial Barcode Scanner is: // | + | The Default settings for the Honeywell 1400G Serial Barcode Scanner is: \\ |
| - | Baud Rate : 115200 | + | Baud Rate : 115200 |
| - | Data Format : 8 Data Bits, No Parity Bit, 1 Stop Bit // | + | Data Format : 8 Data Bits, No Parity Bit, 1 Stop Bit \\ |
| - | On the customer' | + | On the customer' |
| - | Make a note of what COM ports are available because you may need to do a little trial and error to determine which COM port the scanner is physically connected to. // | + | Make a note of what COM ports are available because you may need to do a little trial and error to determine which COM port the scanner is physically connected to. \\ |
| - | Open the properties for the COM port, click on the Port Settings tab and set the Pits Per Second to 115200 bps // | + | Open the properties for the COM port, click on the Port Settings tab and set the Pits Per Second to 115200 bps \\ |
| - | Set the data bits to 8, Parity to None, stop bits to 1 and Flow Control to None. // | + | Set the data bits to 8, Parity to None, stop bits to 1 and Flow Control to None. \\ |
| - | Click OK and exit device manager. | + | Click OK and exit device manager. |
| - | Next Open the POS Device manager on the customer' | + | Next Open the POS Device manager on the customer' |
| - | Go to the Barcode Scanner tab and set the port to the one you noted in the Windows Device Manager. | + | Go to the Barcode Scanner tab and set the port to the one you noted in the Windows Device Manager. |
| - | Again set the settings for the Port to: // | + | Again set the settings for the Port to: \\ |
| - | Baud rate : 115200 bps, Data Format : 8 data bits, no parity bit and 1 stop bit // | + | Baud rate : 115200 bps, Data Format : 8 data bits, no parity bit and 1 stop bit \\ |
| - | Do a test scan and now the barcode should show up correctly in the POS Device manager. | + | Do a test scan and now the barcode should show up correctly in the POS Device manager. |
| - | If the port settings are wrong you may get some information in the preview window, but it will not match the barcode number you scanned. | + | If the port settings are wrong you may get some information in the preview window, but it will not match the barcode number you scanned. |
| - | If your barcode scans correctly in the POS Device Manager, you can open System Five, and test it there. | + | If your barcode scans correctly in the POS Device Manager, you can open System Five, and test it there. |
| - | + | ||
| - | You can't test serial port barcode scanners in the Barcode Scanner section of the setup Wizard. Nothing will scan there. So open an invoice and scan a barcode there, or scan it into the part find screen. // | + | |
| + | You can't test serial port barcode scanners in the Barcode Scanner section of the setup Wizard. Nothing will scan there. So open an invoice and scan a barcode there, or scan it into the part find screen. \\ | ||
honeywell_1400g.txt · Last modified: 2023/11/17 07:15 (5 months ago) by raguilo